How To Make A Mortise And Tenon Joint With A Plunge Router
When the bit stops spinning lift the wood up and off. May 27 2015 Ed Pirnik Gary Junken and Jeff Roos.
Set the router on the end of the piece of poplar to cut the tenon.
How to make a mortise and tenon joint with a plunge router. The block will guide the router as you make the cut. Then use the scale to elevate the plunge stop to the desired mortise depth here 1 116 as shown in the photo below. And repeat the plunge and slide process to hog out more waste.
Httpsyoutubes8h-1FRC6IcIn this video Ill show how to build a mortise jig for your router to be used with Mortise and Tenon JointsThere ar. Zero the depth adjustment scale. Jun 03 2016 Clamp a guide block to your plunge router to align the router with the marked mortise.
Apr 25 2017 There are many ways to make a mortise and tenon and in this video I show you how to use just your router table and a few everyday bits to accomplish this tas. Clamp the work piece in place and make the plunge cut. Start at one end of the mortise and keeping the guide block pressed against the work piece slide the router.
Now use a combination square to mark long layout lines on the plate that indicate the width of the mortise. Oct 02 2014 This completes the first pass. Turn the router on compress the spring in the router bringing the bit down onto the poplar.
Make one pass about halfway through the mortise then plunge all the way on a second pass. Jul 14 2020 Set the router guide at 34-inch to the outside of the knife. Jul 25 2017 Glen Huey teaches the simple steps to create a mortise and tenon joint using a router.
Apr 07 2015 Mortise-and-tenon joints are usually cut on a table saw but they can be made using a router as well. Sep 24 2014 Plunge the router base until the bit passes through the plate so you can access it as a reference for measuring. Use the same principles for whatever wood is used in any project.
Back in 2007 issue 172 of Fine Woodworking magazine featured an article by furniture maker Jeff Miller on how to execute Perfect Mortise-and-Tenon JointsMiller outlined a variety of techniques including how to cut perfect mortises using a specially-built jig that traps the edge guide of a plunge router thus keeping the machine on a. Shut the router off holding the workpiece in place. Set the plunge depth on the router to cut the mortise to correct depth.
0113 - Which bits for mort. Plunge the workpiece onto the spinning router bit while also maintaining pressure against the fence. Apr 18 2020 In this episode Ill be using a plunge router to make both a mortise and tenonIndex0000 - Intro0013 - Which Router Do I Need.
Dec 24 2014 Plunge to bring the bit just in contact with the wood surface then lock the plunge lever and bring the plunge stop to rest on the lowest turret step as shown in the first photo below. Laying Out the Joint. Apr 20 2019 With your workpiece face towards the jig align the right mortise layout line with that right side start mark.
Plywood skin with a cutout for the bit. Raise the bit another 18- to 14-in. Just adjust the size of the router.
Glen Huey teaches the simple steps to create a mortise and tenon joint using a router. Continue these passes increasing the bit height each time until you reach the mortise depth you want. Then slide the bushing from one end of the slot to the other to mark the length of the mortise.
Making a mortise and tenon joint may be a daunting prospect to the novice woodworker but with the proper tools shaping the parts is a quite straightforward process. Cut the mortise with a plunge router. The skin reduces the depth of cut for the first pass so you need not adjust the router Align the line for the left end of the mortise with the start line.
Jul 22 2015 Clamp to the router table a 14. Slide the router across the end of the poplar cutting a 34-inch channel across the end of the poplar. Next slide the router to the left until the bit lines up with the left end of the mortise layout line and set the left stop.
The joints are rounded when using a router but they are just as strong as squared-off mortises and tenons.
